Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum deflection with consideration of initial slippage.
Este exemplo de verificação é baseado no exemplo de verificação 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Um sistema de massa singular com folga e duas molas é desviado primeiro. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
A viga de aço de secção quadrada está sujeita a uma força normal e a uma carga distribuída. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. É apoiada de forma simples. The problem is described using the following parameters. Determine the deflections in the given test times.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Considere o vão da barra ASTM A992 W 18×50 apresentado na Figura 01 e as cargas permanentes e variáveis uniformes. A barra está limitada a uma altura máxima de 45,72 cm (18 pol.). A flecha da carga variável está limitada a L/360. A viga está apoiada de forma simples e contraventada de forma contínua. Verifique a resistência à flexão disponível da viga selecionada com base nos métodos LRFD e ASD.
Uma consola está completamente fixada na extremidade esquerda e carregada por uma força de corte e uma força axial na extremidade direita. The tensile strength is zero and the behavior in the compression remains elastic.
A cantilever of rectangular cross‑section has a mass at the end. Além disso, é carregada por uma força axial. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Verifique se os resultados não são afetados pelo acoplamento de diferentes elementos dimensionais. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Considere o vão da barra ASTM A992 W 18×50 apresentado na Figura 01 e as cargas permanentes e variáveis uniformes. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Determine as flechas máximas do bloco, tendo em consideração ou negligenciando o efeito de corte. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Um cabo de aço ou uma membrana com pinos nas duas extremidades é carregado por uma carga distribuída. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
É definida uma viga em consola com uma secção de viga em I de comprimento L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Um sistema de massa singular com amortecimento está sujeito a uma força de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Uma consola constituída por uma barra de secção circular está sujeita a uma carga uniforme excêntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
O objetivo deste exemplo é demonstrar um processo irreversível causado pelo atrito. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Uma consola com secção circular é carregada por forças de flexão e rotação concentradas. The aim of this verification example is to compare the reduced stress according to the von Mises and Tresca theories.
A cable is loaded by means of a uniform load. Isto resulta numa forma deformada de um segmento circular. Determine the equilibrium force of the cable to obtain the given sag of the cable. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Nos apoios da forquilha está integrada uma estrutura constituída por um perfil em I. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
A placa ortotrópica quadrada em camadas está completamente fixada no seu ponto central e sujeita a compressão. Compare the deflections of the plate corners to check the correctness of the transformation.
Uma consola está completamente fixada na extremidade esquerda e carregada por um momento fletor na extremidade direita. O material tem diferentes resistências plásticas sob tração e compressão.
Uma barra de tração em forma de W de acordo com a ASTM A992 é selecionada para suportar sob tração uma carga permanente de 30 000 kips (13,6 t) e uma carga variável de 90 000 kips (40,8 t). Verify the member strength using both LRFD and ASD.
Uma barra ligeiramente inclinada é carregada com força concentrada, fixada por uma mola numa extremidade e apoiada na outra extremidade. Assuming large deformations and neglecting the member's self-weight, determine its maximum upward deflection.
A estrutura de pórticos de dois pisos está sujeita a cargas sísmicas. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
Nas duas extremidades, está fixado um bloco tridimensional de material elástico-plástico com endurecimento. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.